Cube Test and Slump Test

Hard concrete test were conducted at the age of 7. 1 Find out a levelled surface at the site place the cube moulds.

Concrete Test Machines Panosundaki Pin

The sampling for the cube is also very important.

. Asppek yang mempengaruhi keputusan 23 5 runtuhan 8. The test is an empirical test that measures the. 2 Oil should be applied inside the cube mould after cleaning it properly.

6 Cubes three for 7 days and three for 28 days compression Area for each cube. After the slump test you are sure your concrete is usable. Contact Info 61 7 5524 2230.

Download Report this document. Isi kandungan slump test bil. After conducting slump tests the samples are taken through a slump test.

You need to do a slump test before any cube is tested. It is vital that you do this to examine the suitability of the concrete cube. Concrete Cube Sample Concrete Cube Fails in Test.

01m x 01m x 01m 1 x 10. The internal surface of the standard slump cone is thoroughly cleaned and freed from superfluous moisture. This concrete is poured in the mold and appropriately tempered so as not to have any voids.

100mm x 100mm No. 01m x01m 001m2 Volume for each cube. Introduction The concrete slump test is used for the measurement of a property of fresh concrete.

DATA ANALYSIS SLUMP TEST Slump The height of the cone The height of the concrete cone after the slump 300cm 170cm 13cm CUBE TEST Specimen size. The slump cone is placed on a smooth horizontal waterproof base plate. Kesimpulan 5 cube test 1.

A Sampling Stage of cubes for compressive strength test. It is useful to check concrete mix batches on site before pouring concrete. THEORY To determine the concrete fulfils the required specification 2 types of testing to be conducted are Wet Concrete Testing such as slump compacting factor and Vebe Consistency while hard concrete testing such as cube test and beam flexural strength.

OBJECTIVE To determine the strength and workability of concrete mixture. Keputusan ujian 45 7. 3 Fill the fresh concrete inside the cube mould after checking the Slump test.

In the United Kingdom the slump test is measured in accordance with BS EN 12350-2. If the slump test fails to meet the range limit as dictated by the ritish Standard shown in the table below then the load should be rejected. Site Testing -Slump Test Always do your slump test before making your cubes to ensure the concrete is usable.

Alatan ujian mampatan 7 4. Cube and Slump Test Report. Once youve done the slump test and you are sure your concrete is usable you can introduce the cube moulds.

Fill the cone with the concrete sample in. Embed Size px Transcript of Cube and Slump Test Report. View concrete test cube n slump testdocx from AA 11.

Alatan ujian penurunan 4. The slump cone is then filled with concrete in 4 layers 75mm each tamping each layer 25 times with the help of a tamping rod. For cube test two types of specimens either cubes of 15cm X 15cm X 15cm or 10cm X 10cm x 10cm depending upon the size of aggregate are used.

For most of the works cubical molds of size 15cm x 15cm x 15cm are commonly used. Place the damp slump cone on a flat hard surface. Cube moulds must be manufactured to the specifications of the British Standards Institute.

Tajuk muka surat 1. Usually three cubes are taken from each sample of concrete and the moulds used traditionally have dimensions of 150mm x 150mm x 15mm. 4 The concrete should be filled in three layers and each layer.

Prosedur ujian 4 6. The designer does design the slump specific mix to aid in placement. What To Do If Cube Test Fails In Test After 28 days.

Prosedur ujian 8 6.

Universal Testing Machine Used For Finding Compressive Strength Of Concrete Compressive Strength Concrete Grade Of Concrete

Concrete Cracking For Compressive Strength Of Concrete Compressive Strength Grade Of Concrete Concrete

Compressive Strength Of Concrete Test Compressive Strength Bottle Opener Wall Grade Of Concrete

Concrete Slump Test To Determine The Workability Of Concrete Mix Concrete Slump Test Is Carried Out To C Concrete Slump Test Slumping Civil Engineering Design